BAll crushing toys

[Geezer]

...some are for putting the balls on display for slow crushing.
If one goes slow the balls can be made very flat.

I, too, like to use homemade devises to isolate and display my balls for play and easy access and manipulation, especially for long slow squeezing and crushing...or, rather than crushing, shape distortion would be a better description as flattening implies squeezing one or both between two flat surfaces (which most often causes scrotal pain or pain generated by the stretching of the tunic that surrounds each ball). Rather than scrotal or tunic pain, I seek that deep gut-wrenching pain generated by applying pressure to only a small area of the ball, usually either with my thumb or some other low surface area devise.

Over my many years of genital abuse, I've imagined and tried scores of different techniques and devises on ALL my parts and now that my old dick doesn't work the way it used to, I concentrate my manipulations on my (still healthy and working) balls…and what I enjoy most is squeezing my testicles in such a way that their ovoid shape is pretty severely distorted without flattening the entire ball.

I have a box of homemade toys that I have used and enjoyed over the years and my latest devise is as simple as they come. A short piece of rectangular wood with two holes drilled in it, a pair of 8-10" dowels or steel rods and one of those locking cable ties that electricians use to keep wires together.

The key to how tight the devise can get is the distance between the holes, i.e., the distance between the dowels at the stationary end. If one’s balls are very sensitive to pressure, the holes/dowels should be apart about the smallest diameter of the ball that is to be squeezed. If the abuser has conditioned his balls with years of abuse, the dowels can be much closer together…I’m down to about 1/4” between the holes.

After inserting one end of each dowel into each hole, I spread the open ends and stretching the ball away from my body, slide the devise behind the ball until my scrotum is quite close to the stationary end of the squeezer and then place a cable tie around both dowels and zip it closed trapping the stretched ball into a rather loose pouch of scrotum.

I then take a second devise and while holding the open dowel ends apart, position the devise on the center of the ball and then close the open end of the devise. The size of the scrotal pouch should be small enough so as to keep the ball from slipping out from under the dowels but still be loose enough so that it doesn’t stretch too tightly when pressure is applied to the ball. Once adjusted, the cable tie can be installed and zipped to a tightness that one chooses…and, of course, more pressure can be applied by tightening the cable tie click by click as one chooses. With the cable tie installed fairly close to the squeezed ball, the dowels won’t have any tendency to loosen, at least until the dowels become parallel or until the open ends of the dowels are squeezed tighter than the stationary ends in the block of wood. Once a pair of “dowel squeezers” are installed on one ball, a dedicated abuser could install another pair on his other ball and adjust each separately depending on the degree of pain each ball can take (my right ball becomes almost pain free after I work on it for 15 – 20 minutes…my left one is still quite sensitive and stays hard and turgid even after many more minutes of manipulation).

As one is able to apply more and more pressure, each end of the ball is still free to bulge out and not overly stretch its leathery tunic while that portion between the dowels can be quite severely squeezed producing that wonderful true deep ball pain that many of us seek and enjoy.

I’ve tried making and using a squeezer large enough to use on both balls simultaneously but find that using four squeezers to isolate and to deliver an individual squeeze to each testicle separately produces the best result...and it's pretty kinky to see one's balls so distorted.

The Geezer

PS: I often use a dowel squeezer to isolate each ball when I play with my other clamps and constrictors. The third pic shows my right ball isolated with a dowel squeezer and with two Lobster Claw Rubber Bands applying a continuous squeeze to it.